PUMPKIN CAR STEREO SUPPORT CENTER

Hello friends,

I bought your Android 7.1 for my Opel Vectra C 2.2 Direct assembly date 2006 (original radio siemens cd70). I bought model no. AS0471H-01B at ebay ( https://m.ebay.de/itm/8-Core-Android-7- ... 4794977017 )

I was assured that it would be plug an play and steering wheel remote and Board computer control would work out of the box. Everything else works fine, but it seems wheel keys are not recognized and cannot be learned. Car control app with bc doesnt work either. I already tried setting car model to opel but that did not help.

The provided iso canbus adapter perfectly fits the original cable so everything neccessary is plugged in i guess. Additionally i plugged in WiFi GPS and FM antenna.

What can i do? Please help

Hi,
please first check whether you had connected the follows connectors.

opel.png (371.63 KiB) Viewed 45323 times

If you did and still doesn't works,you can contact our pumpkin customer service or write to support@autopumpkin.com to change an can bus decode box.
Regards

Ok thank you, i really missed this Connection.
Steering wheel control is now working. But 2 problems. Skip forward and backwards are switched, and re learning the Buttons still doesnt seem to work.

The other problem is that steering wheel buttons control radio and board Computer at the same time. Can i change this? I only want to Control the radio with wheel buttons. I read somewhere that with Erisin radios there are several buttons mappings for opel...

Thank you Jammy

Hi,
Any query,you can directly contact our pumpkin customer service and they will help you all issue in time .We are a same team.I knew you contacted them .
About your two issue,could you mind take a photo of your can bus decode box to our customer service ? We want to confirm the info written on the box . And if it is caused by the can bus decode box, our customer service can arrange to send one to you .
Regards

Hello.
I bought the plumpkin AS0471H radio for Opel Meriva A 2007. everything also works well, but the right side of the steering control does not work. the computer (left side) works, but the right (volume etc) does not work.
all wires as above have been connected correctly. the description of the radio shows that it should work properly with Opel Meriva from 2006 to 2008. I have 2007 so it should work.
I bought the radio on Amazon.de on May 28, 2018
# 302-6366475-4018735
Seller: PumpkinCar

Is there any new system upgrade yet?
my radio and software are:
UltraOcta-T8
android 7.1.2
MCU version T8.3.19-11-81-453101-180320
System version
V9.2.2_20180330.180833_KED3-5

and one more question...
Why is the radio sticking out? correctly installed, in addition, I had to cut the housing pieces inside the car to insert the radio. the radio came to an end, the latches slammed, but the radio was very prominent.

Hi,
about the swc, could you tell what function of your right side key button and left side key button ？More details is helpful for us to understand your issue.
About the installation ,this unit really doesn't fit your car perfectly.Hope your kind understandings.
Regards

Hello.
The left side is ok, it works fine (computer control - 1st, 2nd, 3rd, 3rd).
The right side does not work (1. vol +, 2. vol -, 3. switching between radio and music from a memory card, or sd card).
is there any update for my pumpkin?

Hi,thanks for providing clear picture.
I consult the engineers and knew that you externally need to purchase one swc adapter for your car like follows .
https://www.amazon.de/gp/product/B01AY3 ... UTF8&psc=1
I think you originally used the power cable with canbus decorder .Now you can use the other power cable without canbus (ISO cable)in the package,then connect it to the swc adapter.And you need to exchange the yellow wire and the red wire of the ISO cable .

ISO cable.png (286.03 KiB) Viewed 44945 times

Wait for your reply.
Regards

Why should I buy an adapter? after all, you wrote in the sales description that the steering in oplu meriva 2006-2008 operates. nobody said anything about additional costs. besides, I had a xtrons radio before and the control was 100% active, also a canbus on the cable. I think that the canbus module from this radio is damaged. besides, the radio remembers the radio stations and all settings after switching off the engine and removing the keys, so why should I change the yellow wires, red ?? can you tell me in the end whether there is a software update for my pumpkin?

Hi,
ok, let us label that method i told you on last post as method 2.Because the ISO cable is different from the power cable now you were using ,so the yellow wire should be change.However , let us leave method 2 alone first.
Now i suggest you try the following way ( let us label it as method 1).
Please check whether you connect the connectors the canbus signal wire (see following picture)

attention.png (395.39 KiB) Viewed 44849 times

Then you can click the car info app on the meun ,then click BC icon to check whether the canbus decoder works normally or not .
Sorry for making you this trouble and wait for your reply.