How to install 2009 2010 2011 Mazda 6 aftermarket gps navigation system
Posted: Fri Dec 25, 2015 6:08 am
Nowadays installing new dvds for cars is not only to keep up with the trend,but also become a very necessary thing for drivers are increasing at a surprising speed,it means that driving become more disturbed than before.So when you have the desire to buy a fashionable car DVD player for your Mazda 6 of 2009-2011,you go to the exact shop and see various kind of stereo radio and feel confused which one to choose for your car.Don’t worry,if your dashboard of car radio is the same with this one:audio system after installation,aftermarket radio gps nav system with bluetooth music of 2009 2010 2011 Mazda 6,then it is suitable for your car and can be installed without problems.
Next I will show you detailed installation operations for Mazda 6.
1.Unclip and remove the cup holder panel in the center console
2.Unscrew and remove the shift knob,then remove the small pocket panel
3.Unclip and remove trim panels(total 2) beside the shift knob
4.Fasten and remove center trim panel,if you feel hard to do it,then you operate next step first
5.Press in shifter fasten trigger and pull shifter down,make sure a brake on! After this,you can remove the center trim panel
6.Remove two Phillips screws on each side of the center consoles,then remove center consoles
7.Remove left screw and right bolt
8.Fasten and remove the vent panel including the hazard switch above the original player
9.Remove these two screws with a screwdriver
10.Take out original stereo autoradio and disconnect cables with the help of suitable tools
11.Unclip this bolt and make most fine connected here and firm by that bolt
12.Plug these plugs as the picture show
13.After cables are settled to right positions,put new unit into the space
14.Make all set-aside panels back to its original place and firm corresponding screws and shift knob
All installation work has been finished.Before you are begin to install Mazda 6 aftermarket gps navigation, there are some tips to mind:
1.Make sure that you have accomplished car’s parking series before you begin any work
2.Plesae do not use any strong chemicals or cleansers clean the unit
3.When you are installing the wiring, make it as neatly as possible, because the space for it is very small
4.Please don’t remove the GPS SD card when the power is on
To be honest,most of the installation process of radio gps nav system for Mazda series are same in a large proportion,of course it may have some difference during your work,but don’t worry,this is normal and all will be solved only if you make adequate preparation before you start up your removal,such as read installation guide carefully and act as it say,or visit some related websites,for example, and you can also ask dealers for help.
Next I will show you detailed installation operations for Mazda 6.
1.Unclip and remove the cup holder panel in the center console
- 1.png (246.62 KiB) Viewed 14666 times
2.Unscrew and remove the shift knob,then remove the small pocket panel
- 2.png (207.43 KiB) Viewed 14666 times
3.Unclip and remove trim panels(total 2) beside the shift knob
- 3.png (227.44 KiB) Viewed 14666 times
4.Fasten and remove center trim panel,if you feel hard to do it,then you operate next step first
- 4.png (214.87 KiB) Viewed 14666 times
5.Press in shifter fasten trigger and pull shifter down,make sure a brake on! After this,you can remove the center trim panel
- 5.png (200.8 KiB) Viewed 14666 times
6.Remove two Phillips screws on each side of the center consoles,then remove center consoles
- 6.png (251.67 KiB) Viewed 14666 times
7.Remove left screw and right bolt
- 7.png (218.69 KiB) Viewed 14666 times
8.Fasten and remove the vent panel including the hazard switch above the original player
- 8.png (162 KiB) Viewed 14666 times
9.Remove these two screws with a screwdriver
- 9.png (213.13 KiB) Viewed 14666 times
10.Take out original stereo autoradio and disconnect cables with the help of suitable tools
- 10.png (187.07 KiB) Viewed 14666 times
- 10-1.png (221.41 KiB) Viewed 14666 times
11.Unclip this bolt and make most fine connected here and firm by that bolt
- 11.png (188.88 KiB) Viewed 14666 times
- 11-1.png (194.95 KiB) Viewed 14666 times
12.Plug these plugs as the picture show
13.After cables are settled to right positions,put new unit into the space
14.Make all set-aside panels back to its original place and firm corresponding screws and shift knob
All installation work has been finished.Before you are begin to install Mazda 6 aftermarket gps navigation, there are some tips to mind:
1.Make sure that you have accomplished car’s parking series before you begin any work
2.Plesae do not use any strong chemicals or cleansers clean the unit
3.When you are installing the wiring, make it as neatly as possible, because the space for it is very small
4.Please don’t remove the GPS SD card when the power is on
To be honest,most of the installation process of radio gps nav system for Mazda series are same in a large proportion,of course it may have some difference during your work,but don’t worry,this is normal and all will be solved only if you make adequate preparation before you start up your removal,such as read installation guide carefully and act as it say,or visit some related websites,for example, and you can also ask dealers for help.
- 3.png (227.44 KiB) Viewed 14666 times
- 7.png (218.69 KiB) Viewed 14666 times