Solution:
1. Set the boot logo:
Settings---CAR---Factory settings--Enter the password "126 "--Car logo--APPLY--EXIT- -Press "RES" button to restart.
2. Set the LED button light color:
Settings---CAR--LED settings---select the favorite color
Video operation link:
https://mega.nz/file/mbwGXRKJ#8X-Cbk0M6 ... ZqddrcQzu8
Statistics: Posted by Jammy — Tue Jun 20, 2023 9:00 am
]]>
Please refer to the following operation video to solve the problem, video operation to obtain the link:
1. screen reverse reaction - operation video link:
https://mega.nz/file/nKQAEZiR#VUfhGu4dl ... ItUDXepXnU
2. Touch screen reverse reaction and button can not be used - operation video link:
https://mega.nz/file/DbhhzQSL#VrXWzac3f ... D9-6UlaxeU
Statistics: Posted by Jammy — Tue Jun 06, 2023 8:20 am
]]>
Solution countermeasures:
1. Adjust the navigation volume according to the following operation video.
Video operation reference:
https://mega.nz/file/6fgmnBZS#-d02E17-M ... y11ynW-dtU
2. If you can't solve the problem after adjusting the volume, you can try to reinstall the system
reinstall the system operation reference:
https://mega.nz/file/WTxlFYiC#ZzhmMgrrP ... XKFH8HPa2A
Steps to install the brushing software：
You can install the updated firmware by following these steps and the attached photos:
https://mega.nz/file/WTxlFYiC#ZzhmMgrrP ... XKFH8HPa2A
1. Please kindly decompress the updated file after downloading it from PC.
2. Copy the folder to the root directory of a blank USB drive. Insert the USB drive into the USB port.
3. Then click "Settings" on the main menu and go to "System" settings.
4. Click the "System Update" button, select "Erase data and format flash memory!", then click the "Install" button to update the system.
5. The system may start to update. This will take about 3 minutes for the software update. The radio will then reboot. When it goes to the main menu, the upgrade is complete. You can then unplug the USB drive. (Note: You cannot disconnect the power during the software upgrade and system reboot.) .
Statistics: Posted by Jammy — Thu May 11, 2023 9:20 am
]]>
]]>
I'm trying to confirm the speaker output specifications on the Andorid 10 7" Double Din stereo. I have the model shown in the following link:
https://www.autopumpkin.co.uk/collectio ... rse-camera
I cant find anything in the user guide that I have, and I'm looking to replace my speakers and would like the shop to best match the speakers for the correct wattage and Ohms etc for best audio quality when on full volume.
Thanks in advance
Statistics: Posted by phoenix3dfx225 — Thu Feb 10, 2022 1:44 pm
]]>
Could you please send us some photos of the power adapter for your 2001 Audi A4?
Then our engineer will check if the adapter fits our android 11 car radio.
Best Regards
Autopumpkin
Statistics: Posted by Jammy — Fri Dec 31, 2021 9:47 am
]]>
Could you please tell us the SKU number of your car radio then take a video of the button problem?
Best Regards
Autopumpkin
Statistics: Posted by Jammy — Fri Dec 31, 2021 9:43 am
]]>
I've got a Navi for BMWe46 from pumpkin, with GPS from IGO and the software is WinCE.
The turn on/off/volume switch broke and i've solder a new one. Now when I Install the Navi on the car, all the red LEDs from the NAVI flash and keep blinking and the navi wont turn on. So I've switched the new switch with the one off the balance switch and it's all the same.
So I'm asking to the forum, what could be the flashing LEDS sign ? and if it is a software or hardware problem ? I think that when I take the switch off and resolder a new one, maybe I've desprogram anything.
Please help me.
Kind regards
Statistics: Posted by nft — Mon Dec 27, 2021 10:23 am
]]>
]]>
]]>
]]>
I have model AA0495B-B02 Android.
I have tried every wiring combination to get SWC to work but I cannot get even 1 button to respond.
I have removed the SWC assembly from the steering wheel and measured each button resistance to confirm the circuit.
I have connected SWC assembly to to the stereo to eliminate car wiring loom.
I have factory reset the stereo.
I have tested using a resistor but can only get the stereo to register a button when I ground to Key1 or Key2. It does not register the resistor between Key1 and Key2.
I have tried the steering wheel ground black wire to ground and floating.
I have tried the steering wheel ground black tied to Key1 and Key2 seperately with no affect.
Please can you look at the wiring diagram of the factory SWC circuit and tell me which wire to connect to each stero wire? Wires to stero are the 1750 BK/YE and 1796 BN. There is no ground in this resistor circuit.
Thank you.
Statistics: Posted by whatsmyname — Fri Nov 19, 2021 9:22 pm
]]>
]]>
This car stereo has been out of production, If your car radio does not work on 12v, it is the car radio issue, maybe the mainboard is broken
Would you mind getting a new android 11 car stereo?
Best Regards
Autopumpkin
Howdy,
unfortunately, one of the RQ0269 stopped working.
The car was sitting unused for maybe a year and of course battery was removed.
The head unit has power on the +12v and ignition key (ACC) wires, but the screen is just black - does not boot.
The order numbers (Amazon) of my RQ0269 are
Ordered on November 4, 2016 Order# 116-4491240-2773030
Ordered on October 16, 2016 Order# 116-4268175-9668244
Any hints are appreciated
Oskar
Statistics: Posted by oskaratk — Thu Nov 18, 2021 4:58 am
]]>
Thanks for your answer!
Thanks on the offer, but i think I'll try another brand! This car stereo had little use, so I guess it was just bad luck on my part.
Best regards,
Ricardo Almeida
Statistics: Posted by Ricardo Almeida — Mon Sep 27, 2021 4:26 pm
]]>