Firmware for RQ0276E

[Hamish]

Jammy
any suggested solution to my recovery menu problem
hamish

[Jammy]

[Hamish]

Thanks for all the feedback. Answering the questions in order
My Ebay id is hami5h.gray. the Transaction ID 6PW170391T791435S.

Original status
MCU-Version MTCC-KLD6-V2.97
Kernel-Version 3.0.101+
Build-Number rk3188-userdebug 22082016.17:46:35
Due to the minor response type issues I flashed the update using the below link from a post on this forum
https://mega.nz/#!ZYFCGIZY!vlVpc2S_zPiz ... xD2mRZkC60
This worked perfectly except it seemed even slower and was in fact turned out to be a step back in issue
New status
MCU-Version MTCC-KLD6-V2.97
Kernel-Version 3.0.101+
Build-Number rk3188-userdebug 05082016.16:30:02
Seeing a new version posted on the 7th Nov below
https://mega.nz/#!lFVVWS7Q!WvezHo2glWLu ... BNYnqVArUE
I flashed this via update in system menu
It stalled and after 30min I switched off and switched back on
It booted up with many error messages including the following

E:failed to mount /dev/cache /dev/block/rknand_cache (block device required)
E:Can't mount /cache/recovery/last_log
E:can't open /cache/recovery/last_log
E:Can't mount /cache/recovery/last_ install
E:can't open /cache/recovery/last_ install
E:Can't mount /cache/recovery/last_kmsg
E:can't open /cache/recovery/last_kmsg
It was in the system recovery menu.
I went to reboot and it booted into normal operational mode with as far as I can test everything working.
Status was still
MCU-Version MTCC-KLD6-V2.97
Kernel-Version 3.0.101+
Build-Number rk3188-userdebug 05082016.16:30:02
I then tried the https://mega.nz/#!lFVVWS7Q!WvezHo2glWLu ... BNYnqVArUE update again from the system recovery menu. update from SD card
Same errors again and no update
I have redownloaded the image from the links, no change.
I have flashed many android devices over the years without issues. I do know what I am doing
Tonight I input the factory settings root password and with a file explorer I can examine all the folders, many seem to be empty. eg Cache/ has nothing in it or sub folders
If you want I can check what is in what
Is it possible to create a SD card to enable boot and flash from SD card using create upgrade disk tool V1.4

[Hamish]

corrected the problem by creating bootable SD Card, put image on usb stick. booted from SD card then choose install image from usb stick. all now working

Hamish

[torstenwegner]

Hello
I have since firmware update eon problem with MCU.
If I want to open in factory setting with password 126
Password is wrong
Do I need new mcu?

Please help me
Torsten

[Jammy]

[torstenwegner]

got from you the new firmware
And password is safe 126
My mcu is on picture

20161108_114738.jpg (801.42 KiB) Viewed 2178 times

[Jammy]

Hi,
Thanks for your information about the unit.
The MCU on your unit is the latest one.
Regards

[torstenwegner]

and what now ?
I can not go into the factory setting
Do they now exchange the radio?...

[Jammy]

Hi,
Normally you don't need to enter factory settings to change anything.
Could you please tell us what problem you had?
Here is a link of another version mcu for your unit, you can install it to check.
https://mega.nz/#!YElSyAhK!qUmyJCjNHudQ ... 1zIx_xKsYA
And you can also try no password to enter the factory setting, maybe there is a small system bug on our unit.
Regards